NECAL 8899-60 Pressure Sensitive Adhesive Print Friendly Version
Adhesive Description:
NECAL 8899-60 is a foam supported pressure sensitive adhesive that exhibits very high performance.
Features:
NECAL 8899-60 is primarily intended for use where extreme high performance is needed. 8899-60 has superior impact and vibration resistance.
Physical Properties:
Composition: Acrylic based Adhesive
Release liner: Available with P or W liner
Thickness: Total construction 65 mils + or – 10%
Scrim: Black polyurethane foam
Adhesion: 80-100 oz./in.
Tensile: 90 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 225°F maximum
Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate. Use firm pressure to obtain maximum contact. Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.
Storage:
The shelf life of this material is al least two years when stored in a cool, dry place.
Notice:
The information shown here represents typical values that may vary with each application. The values are not intended to be a performance guarantee. Users should determine, prior to use, the suitability of this material for their application.
Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.
Tags:
Foam Products,
Low Temperature,
Necal Brand Products,
Single Coated Foam Tape,
Acrylic PSA Adhesive,
High Performance,
High Tack Adhesive,
Temperature Resistant,
Strong Bond,
Rough/Uneven Surface Adhesive,
Double Coated Foam Tape,
Black Polyurethane Foam,
Polyurethane Foam
NECAL 8899-45 Pressure Sensitive Adhesive Print Friendly Version
Adhesive Description:
NECAL 8899-45 is a foam supported pressure sensitive adhesive that exhibits very high performance.
Features:
NECAL 8899-45 is primarily intended for use where extreme high performance is needed. 8899-45 has superior impact and vibration resistance.
Physical Properties:
Composition: Acrylic based Adhesive
Release liner: Available with P or W liner
Thickness: Total construction 48 mils + or – 10%
Scrim: Black polyurethane foam
Adhesion: 80-100 oz./in.
Tensile: 90 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 225°F maximum
Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate. Use firm pressure to obtain maximum contact. Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.
Storage:
The shelf life of this material is al least two years when stored in a cool, dry place.
Notice:
The information shown here represents typical values that may vary with each application. The values are not intended to be a performance guarantee. Users should determine, prior to use, the suitability of this material for their application.
Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.
Tags:
Foam Products,
Low Temperature,
Necal Brand Products,
Single Coated Foam Tape,
Acrylic PSA Adhesive,
High Performance,
High Tack Adhesive,
Temperature Resistant,
Strong Bond,
Rough/Uneven Surface Adhesive,
Double Coated Foam Tape,
Black Polyurethane Foam,
Polyurethane Foam
NECAL 8899-30 Pressure Sensitive Adhesive Print Friendly Version
Adhesive Description:
NECAL 8899-30 is a foam supported pressure sensitive adhesive that exhibits very high performance.
Features:
NECAL 8899-30 is primarily intended for use where extreme high performance is needed. 8899-30 has superior impact and vibration resistance.
Physical Properties:
Composition: Acrylic based Adhesive
Release liner: Available with P or W liner
Thickness: Total construction 38 mils + or – 10%
Scrim: Black polyurethane foam
Adhesion: 80-100 oz./in.
Tensile: 90 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 225°F maximum
Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate. Use firm pressure to obtain maximum contact. Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.
Storage:
The shelf life of this material is al least two years when stored in a cool, dry place.
Notice:
The information shown here represents typical values that may vary with each application. The values are not intended to be a performance guarantee. Users should determine, prior to use, the suitability of this material for their application.
Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.
Tags:
Foam Products,
Low Temperature,
Necal Brand Products,
Single Coated Foam Tape,
Acrylic PSA Adhesive,
High Performance,
High Tack Adhesive,
Temperature Resistant,
Strong Bond,
Rough/Uneven Surface Adhesive,
Double Coated Foam Tape,
Black Polyurethane Foam
NECAL 8899-15 Pressure Sensitive Adhesive Print Friendly Version
Adhesive Description:
NECAL 8899-15 is a foam supported pressure sensitive adhesive that exhibits very high performance.
Features:
NECAL 8899-15 is primarily intended for use where extreme high performance is needed. 8899-15 has superior impact and vibration resistance.
Physical Properties:
Composition: Acrylic based Adhesive
Release liner: Available with P or W liner
Thickness: Total construction 20 mils + or – 10%
Scrim: Black polyurethane foam
Adhesion: 80-100 oz./in.
Tensile: 90 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 225°F maximum
Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate. Use firm pressure to obtain maximum contact. Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.
Storage:
The shelf life of this material is two years when stored in a cool, dry place.
Notice:
The information shown here represents typical values that may vary with each application. The values are not intended to be a performance guarantee. Users should determine, prior to use, the suitability of this material for their application.
Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.
Tags:
Foam Products,
Low Temperature,
Necal Brand Products,
Single Coated Foam Tape,
Acrylic PSA Adhesive,
High Performance,
High Tack Adhesive,
Temperature Resistant,
Strong Bond,
Rough/Uneven Surface Adhesive,
Mounting Tape,
Double Coated Foam Tape,
Black Polyurethane Foam,
Polyurethane Foam
NECAL 8875 Pressure Sensitive Adhesive Print Friendly Version
Adhesive Description:
NECAL 8875 is a supported pressure sensitive adhesive displaying excellent tack.
Features:
NECAL 8875 will adhere to many substrates. 8875 is highly recommended for rough textured surfaces that have low contact areas. It can be used where vibration deadening is required.
Physical Properties:
Composition: Acrylic based Adhesive
Release liner: Available with P or W liner
Thickness: Total construction 32 mils + or – 10%
Scrim: Polyurethane open-celled foam
Adhesion (PSTC-1 std.): 75-90 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 70 p.s.i.
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 225°F maximum
Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate. Use firm pressure to obtain maximum contact. Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.
Storage:
The shelf life of this material is at least two years when stored in a cool, dry place.
Notice:
The information shown here represents typical values that may vary with each application. The values are not intended to be a performance guarantee. Users should determine, prior to use, the suitability of this material for their application.
Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.
Tags:
Foam Products,
Low Temperature,
Necal Brand Products,
Acrylic PSA Adhesive,
High Tack Adhesive,
Temperature Resistant,
Strong Bond,
Rough/Uneven Surface Adhesive,
Double Coated Foam Tape,
Polyurethane Foam
NECAL 8808 Pressure Sensitive Adhesive Print Friendly Version
Adhesive Description:
NECAL 8808 is a supported pressure sensitive adhesive displaying high tack and good creep resistance.
Features:
NECAL 8808 will adhere to many substrates. 8808’s thickness gives good conformability to rough or uneven surfaces (i.e. mold marks, etc.).
Physical Properties:
Composition: Acrylic based Adhesive
Release liner: Available with P or W liner
Thickness: Total construction 9.0 mils
Scrim: 2.0 mils Non-woven polyester
Adhesion (PSTC-1 std.): 350-375 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 180 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 225°F maximum
Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate. Use firm pressure to obtain maximum contact. Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.
Storage:
The shelf life of this material is at least two years when stored in a cool, dry place.
Notice:
The information shown here represents typical values that may vary with each application. The values are not intended to be a performance guarantee. Users should determine, prior to use, the suitability of this material for their application.
Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.
Tags:
Low Temperature,
Necal Brand Products,
Adhesive Transfer Tape,
Acrylic PSA Adhesive,
Double Coated Tape,
High Performance,
High Tack Adhesive,
Temperature Resistant,
VSB (very strong bond),
Rough/Uneven Surface Adhesive,
Mounting Tape
NECAL 8608 Supported Pressure Sensitive Adhesive Print Friendly Version
Adhesive Description:
NECAL 8608 is an extremely aggressive supported pressure sensitive adhesive.
Features:
NECAL 8608 was designed for adhesion to low energy surfaces (i.e. polyethylene and polypropylene) but especially for rough or textured surfaces.
Physical Properties:
Composition: Modified Acrylic Adhesive
Release liner: Available with P, or W liner
Thickness: Total construction 7.8-8.4 mil
Scrim: 2.0 mils non-woven polyester
Adhesion (PSTC-1 std.): 120-150 oz./in. (Aluminum/Polypropylene) 340-360 oz./in. (Aluminum/Stainless steel)
Tensile (Polyester to SS, 1 sq.in.): 250 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 5 days +
Application temperature: 50°F Minimum
Service temperature range: -20°F to 270°F
Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate. Use firm pressure to obtain maximum contact. Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.
Storage:
The shelf life of this material is at least two years when stored in a cool, dry place.
Notice:
The information shown here represents typical values that may vary with each application. The values are not intended to be a performance guarantee. Users should determine, prior to use, the suitability of this material for their application.
Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.
Tags:
Low Temperature,
Necal Brand Products,
Adhesive Transfer Tape,
Acrylic PSA Adhesive,
Differential Tape,
Double Coated Tape,
High Tack Adhesive,
VSB (very strong bond),
Low Surface Energy,
Rough/Uneven Surface Adhesive
NECAL 8495 Pressure Sensitive Adhesive Print Friendly Version
Adhesive Description:
NECAL 8495 is a supported pressure sensitive adhesive displaying excellent tack.
Features:
NECAL 8495 will adhere to many substrates. 8495 is highly recommended for rough textured surfaces that have low contact areas. It can be used where vibration deadening is required.
Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P or W liner
Thickness: Total construction 32 mils + or – 10%
Scrim: 30 mil polyurethane open-celled foam
Adhesion (PSTC-1 std.): 95-120 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 90 p.s.i.
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 300°F maximum
Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate. Use firm pressure to obtain maximum contact. Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.
Storage:
The shelf life of this material is two years when stored in a cool, dry place.
Notice:
The information shown here represents typical values that may vary with each application. The values are not intended to be a performance guarantee. Users should determine, prior to use, the suitability of this material for their application.
Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.
Tags:
Foam Products,
Low Temperature,
Necal Brand Products,
Acrylic PSA Adhesive,
High Tack Adhesive,
Temperature Resistant,
Strong Bond,
Rough/Uneven Surface Adhesive,
Mounting Tape,
Double Coated Foam Tape,
Automotive Approved,
open-cell polyurethane
NECAL 8392 Supported Pressure Sensitive Adhesive Print Friendly Version
Adhesive Description:
NECAL 8392 is a polyethylene foam supported pressure sensitive adhesive displaying high tack and good creep resistance.
Features:
NECAL 8392 will adhere to many substrates, including low energy surfaces such as polyethylene and polypropylene.
Physical Properties:
Composition: Acrylic based adhesive (both sides)
Release liner: Available with P or W liner
Thickness: Total construction 16 mils + or – 10%
Scrim: Black polyurethane foam
Adhesion (PSTC-1 std.): 50-60 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 90 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 195°F maximum
Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate. Use firm pressure to obtain maximum contact. Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.
Storage:
The shelf life of this material is al least two years when stored in a cool, dry place.
Notice:
The information shown here represents typical values that may vary with each application. The values are not intended to be a performance guarantee. Users should determine, prior to use, the suitability of this material for their application.
Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.
Tags:
Foam Products,
Low Temperature,
Necal Brand Products,
Single Coated Foam Tape,
Acrylic PSA Adhesive,
High Tack Adhesive,
Low Surface Energy,
Rough/Uneven Surface Adhesive,
Double Coated Foam Tape,
Black Polyurethane Foam,
Polyurethane Foam
NECAL 8292 Supported Pressure Sensitive Adhesive Print Friendly Version
Adhesive Description:
NECAL 8292 is a polyethylene foam supported pressure sensitive adhesive displaying high tack and good creep resistance.
Features:
NECAL 8292 will adhere to many substrates, including low energy surfaces such as polyethylene and polypropylene.
Physical Properties:
Composition: Modified Acrylic based adhesive (both sides)
Release liner: Available with P or W liner
Thickness: Total construction 32 mils + or – 10%
Scrim: Black or White polyethylene closed cell foam
Adhesion (PSTC-1 std.): 50-60 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 90 p.s.i., foam failure
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 195°F maximum
Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate. Use firm pressure to obtain maximum contact. Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.
Storage:
The shelf life of this material is two years when stored in a cool, dry place.
Notice:
The information shown here represents typical values that may vary with each application. The values are not intended to be a performance guarantee. Users should determine, prior to use, the suitability of this material for their application.
Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.
Tags:
Foam Products,
Low Temperature,
Necal Brand Products,
Single Coated Foam Tape,
Acrylic PSA Adhesive,
High Tack Adhesive,
Low Surface Energy,
Rough/Uneven Surface Adhesive,
Mounting Tape,
Double Coated Foam Tape,
Automotive Approved,
Black Polyethylene Foam
