NECAL Label Stock      Print Friendly Version

Adhesive Description:

NECAL Label Stock is made up of various combinations of face stocks, adhesives and 90 lb. layflat release liner which are manufactured to meet customer requirements.

Features:
NECAL Label Stock can be manufactured using a variety of Pressure Sensitive Adhesives, which include high temperature acrylic, low surface tension acrylic, a rubber base, general purpose acrylic and others.  It can be supplied with a variety of face stocks, which can include: .001 Brite Chrome PET, .0055 Brite or Brushed Chrome PET, .002 Brite or Brushed Chrome PET, .008 Brite or Brushed Chrome PET.  Other face stocks that those listed above may also be available.

Physical Properties:
Composition: Acrylic or Rubber Based Adhesive
Release liner: 90 lb. polycoated release liner
Thickness: Can range from ½ mil to 4 mils thick dependent upon the application.
Adhesion: Dependent upon adhesive utilized
Tensile: Dependent upon adhesive utilized
Shear adhesion: Dependent upon adhesive utilized
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum, Maximum temperature is dependent upon Adhesive utilized

Bonding Instructions:
Remove the release liner and apply to clean, dry substrate.  Use of air, hydraulic or mechanical bonding press is recommended with a pressure of 40-60 P.S.I. with a dwell time of 2 – 5 seconds to insure intimate contact is achieved between nameplate and substrate.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 9210 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 9210 is an unsupported film of pressure sensitive adhesive that displays high initial tack and peel. It is UL recognized to Standard UL 969 (PGGU2 Component - Marking and Labeling Systems Materials).

Features:
NECAL 9210 will adhere to many substrates including polyethylene and polypropylene.

Physical Properties:
Composition: Rubber based Adhesive
Release liner: Available with P or W liner
Thickness: Total construction 2.0 mils
Adhesion: 120 - 140 oz./in.
Tensile: 120 p.s.i.
Shear adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 190°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is at least two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 9200 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 9200 is an unsupported film of pressure sensitive adhesive that displays high initial tack and peel. It is UL recognized to Standard UL 969 (PGGU2 Component - Marking and Labeling Systems Materials).

Features:
NECAL 9200 will adhere to many substrates including polyethylene and polypropylene.

Physical Properties:
Composition: Rubber based Adhesive
Release liner: Available with P or W liner
Thickness: Total construction 2.0 mils
Adhesion: 150 - 180 oz./in.
Tensile: 100 p.s.i.
Shear adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 170°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 8493 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 8493 is a supported rubber based pressure sensitive adhesive displaying high tack and good creep resistance.

Features:
NECAL 8493 will adhere to many substrates, including polyethylene and polypropylene.

Physical Properties:
Composition: Rubber based adhesive
Release liner: Available with P or W liner
Thickness: Total construction 4 mils
Scrim: 48 gauge polyester
Adhesion (PSTC-1 std.): 60 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 137 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 170°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 8192 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 8192 is a white or black foam supported adhesive with superior tack.

Features:
NECAL 8192 is primarily intended for applications with extremely rough substrates such as cast iron, cement, etc.  8192 has excellent impact and vibration resistance.  8192 has excellent adhesion to polyethylene and polypropylene as well as other substrates.

Physical Properties:
Composition: Rubber based adhesive
Release liner: Available with P or W liner
Thickness: Total construction 32 mil + or – 10%
Scrim: White Polyethylene closed-cell foam
Adhesion (PSTC-1 std.): 160-170 oz./in., 80-100 to polyethylene and polypropylene
Tensile (Polyester to SS, 1 sq.in.): 65 p.s.i. foam failure
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 170°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 4500 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 4500 is a high strength, high shear, pressure sensitive adhesive that displays very aggressive initial tack, used only to manufacture label stock.It is UL recognized to Standard UL 969 (PGGU2 Component - Marking and Labeling Systems Materials).

Features:
NECAL 4500 has excellent adhesion to most substrates, including polyethylene and polypropylene.

Physical Properties:
Composition: Rubber based adhesive
Release liner: Available with P, P1, W or W1 liner
Thickness: Total construction 1.0 – 2.0 mils dependent upon application
Scrim: 2 mil chrome, 2 mil brush chrome, 1 mil mylar, 2 mil mylar, and 4 mil mylar
Adhesion: 80-100 oz./in. | 40 – 50 oz./in. to polyethylene and polypropylene
Tensile: 70 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 170°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 1330FP Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

Features:
NECAL 1330FP is a lightweight, conformable pressure sensitive tape for window flashing and housewrap film splicing.

Physical Properties:
Composition: Rubber based adhesive
Release liner: Available with W liner
Thickness: Total construction 30 mil + or – 10%
Scrim: White Polyethylene foam

(1)  Foam split failure
(2)  Tyvek split failure
(3)  All samples reinforced with 2 mil polyester film as test values exceeded foam strength.
(4)  Samples bonded at 20ºF, left at 20°F for 15 min. then tested at room temp.
(5)  Samples were taken down, had not failed and showed little or no movement.

Permeability
Water vapor transmission rate: .04 or less grams per hour
Water absorption: 200 or less grams per square meter
Permeability is based on foam material only without adhesive.  Testing with adhesive would reduce water vapor and absorption considerably.

Surface Preparation
All surfaces must be dry, smooth, and free of dust, dirt, and debris.  Any loose debris must be cleaned off before application.

Application:
Cut pieces to be adhered to length.  Remove release liner, position and smooth into place from one end to the other eliminating as many air pockets as possible.  Apply based on local code and or standard building practices.  Overlaps should be a minimum of 2 inches.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.