NECAL 8608 Supported Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 8608 is an extremely aggressive supported pressure sensitive adhesive.

Features:
NECAL 8608 was designed for adhesion to low energy surfaces (i.e. polyethylene and polypropylene) but especially for rough or textured surfaces.

Physical Properties:
Composition: Modified Acrylic Adhesive
Release liner: Available with P, or W liner
Thickness: Total construction 7.8-8.4 mil
Scrim: 2.0 mils non-woven polyester
Adhesion (PSTC-1 std.): 120-150 oz./in. (Aluminum/Polypropylene) 340-360 oz./in. (Aluminum/Stainless steel)
Tensile (Polyester to SS, 1 sq.in.): 250 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 5 days +
Application temperature: 50°F Minimum
Service temperature range: -20°F to 270°F

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is at least two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 8517 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 8517 is a supported pressure sensitive adhesive with a general purpose modified acrylic on one side and a general purpose acrylic on the other side displaying high tack.

Features:
NECAL 8517 is designed for low energy surfaces (i.e. polyethylene and polypropylene) utilizing the acrylic side of the system.  The modified acrylic side should be bonded to the nameplate only.

Physical Properties:
Composition: General purpose acrylic on one side and a modified acrylic on the other side
Release liner: Available with H, P or W liner
Thickness: Total construction 6.2-7.0 mils
Scrim: 1 mil polyester
Adhesion (PSTC-1 std.): 80-100 oz./in. (Aluminum/Polypropylene)
Tensile (Polyester to SS, 1 sq.in.): 220-250 oz./in.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 24 hours +
Application temperature: 50°F Minimum
Service temperature range: -20°F minimum to 195°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 8502 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 8502 is a supported pressure sensitive adhesive with a general purpose acrylic on one side and a modified acrylic on the other side displaying high tack.

Features:
NECAL 8502 is designed for low energy surfaces (i.e. polyethylene and polypropylene) utilizing the modified acrylic side of the system.  The acrylic side should be bonded to the nameplate only.

Physical Properties:
Composition: General purpose acrylic on one side and a modified acrylic on the other side
Release liner: Available with P or W liner
Thickness: Total construction 4.0 mils
Scrim: .00048 mil polyester
Adhesion (PSTC-1 std.): 80-100 oz./in. (Aluminum/Polypropylene)
Tensile (Polyester to SS, 1 sq.in.): 230 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 24 hours +
Application temperature: 50°F Minimum
Service temperature range: -20°F minimum to 300°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 3400 Removable Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 3400 is a supported film of removable pressure sensitive adhesive that displays good tack and adhesion but is easily removed with no residue from most surfaces.  A permanent adhesive is on one side of the polyester scrim and a removable adhesive is on the opposite side.  The permanent adhesive is intended to be bonded to the appliqué and the removable adhesive is intended to be bonded to the substrate.

Physical Properties:
Composition: Acrylic based adhesive (both sides)
Release liner: Available with P or W liner
Thickness: Total construction 5 mils
Scrim: 1 mil polyester
Adhesion: 200-220 oz./in. (removable)
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 195°F maximum

Bonding Instructions:
Apply to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact Necal Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 3300 Removable Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 3300 is a supported film of removable pressure sensitive adhesive that displays good tack and adhesion but is easily removed with no residue from most surfaces.  A permanent adhesive is on one side of the polyester scrim and a removable adhesive is on the opposite side.  The permanent adhesive is intended to be bonded to the appliqué and the removable adhesive is intended to be bonded to the substrate.

Physical Properties:
Composition: Acrylic based adhesive (both sides)
Release liner: Available with P or W liner
Thickness: Total construction 3.5 mils
Scrim: .5 mil polyester
Adhesion: 5-10 oz./in. (removable)
Application temperature: 50°F Minimum
Service temperature range: 0°F minimum to 120°F maximum

Bonding Instructions:
Apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is at least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 3200 Removable Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 3200 is a supported removable pressure sensitive adhesive that displays good tack and adhesion but is easily removed with no residue from most surfaces.  A permanent adhesive is on one side of the polyester scrim and a removable adhesive is on the opposite side.  The permanent adhesive is intended to be bonded to the appliqué and the removable adhesive is intended to be bonded to the substrate.

Physical Properties:
Composition: Acrylic based adhesive (both sides)
Release liner: Available with P or W liner
Thickness: Total construction 3.5 mils
Scrim: .5 mil polyester
Adhesion: 10-20 oz./in. (removable).
Application temperature: 50°F Minimum
Service temperature range: 0°F minimum to 120°F maximum

Bonding Instructions:
Apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is at least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.