NECAL Label Stock      Print Friendly Version

Adhesive Description:

NECAL Label Stock is made up of various combinations of face stocks, adhesives and 90 lb. layflat release liner which are manufactured to meet customer requirements.

Features:
NECAL Label Stock can be manufactured using a variety of Pressure Sensitive Adhesives, which include high temperature acrylic, low surface tension acrylic, a rubber base, general purpose acrylic and others.  It can be supplied with a variety of face stocks, which can include: .001 Brite Chrome PET, .0055 Brite or Brushed Chrome PET, .002 Brite or Brushed Chrome PET, .008 Brite or Brushed Chrome PET.  Other face stocks that those listed above may also be available.

Physical Properties:
Composition: Acrylic or Rubber Based Adhesive
Release liner: 90 lb. polycoated release liner
Thickness: Can range from ½ mil to 4 mils thick dependent upon the application.
Adhesion: Dependent upon adhesive utilized
Tensile: Dependent upon adhesive utilized
Shear adhesion: Dependent upon adhesive utilized
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum, Maximum temperature is dependent upon Adhesive utilized

Bonding Instructions:
Remove the release liner and apply to clean, dry substrate.  Use of air, hydraulic or mechanical bonding press is recommended with a pressure of 40-60 P.S.I. with a dwell time of 2 – 5 seconds to insure intimate contact is achieved between nameplate and substrate.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 4800 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 4800 is an unsupported film of pressure sensitive adhesive which displays excellent bond and initial tack.

Features:
NECAL 4800 adheres to most substrates, including aluminum, brass, steel, glass, enamels and plastics such as polystyrene, ABS and acrylic.  Because of its thickness, 4800 is recommended for use on rough surfaces.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P, P1, W or W1 liner
Thickness: Total construction 1.0 – 4.0 mils dependent upon application
Scrim: 2 mil chrome, 2 mil brush chrome, 1 mil mylar, 2 mil mylar, and 4 mil mylar
Adhesion: 325 - 350 oz./in. at 4.0 mils
Tensile: 180 p.s.i.
Shear adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 225°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 4700 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 4700 is an unsupported film of pressure sensitive adhesive which displays excellent bond and initial tack.

Features:
NECAL 4700 is designed for bonding to polypropylene and polyethylene.  4700 adheres to many other substrates.

Physical Properties:
Composition: Modified Acrylic based adhesive
Release liner: Available with P, P1, W or W1 liner
Thickness: Total construction 1.0 – 4.0 mils dependent upon application
Scrim: 2 mil chrome, 2 mil brush chrome, 1 mil mylar, 2 mil mylar, and 4 mil mylar
Adhesion: 60-75 oz./in. (Aluminum/Polypropylene) 340 – 360 oz./in. (Aluminum/Stainless)Tensile: 225 p.s.i.
Tensile: 225 p.s.i.
Shear adhesion: 24 hours +
Application temperature: 50°F Minimum
Service temperature range: -20°F minimum to 195°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 4600 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 4600 is an unsupported film of pressure sensitive adhesive displaying high tack and good creep resistance.

Features:
NECAL 4600 will adhere to many substrates, supplied as a bubble free film for backlit applications.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P, P1, W or W1 liner
Thickness: Total construction 1.0 – 4.0 mils dependent upon application
Scrim: 2 mil chrome, 2 mil brush chrome, 1 mil mylar, 2 mil mylar, and 4 mil mylar
Adhesion (PSTC-1 std.): 80-85 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 150 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 400°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 4500 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 4500 is a high strength, high shear, pressure sensitive adhesive that displays very aggressive initial tack, used only to manufacture label stock.It is UL recognized to Standard UL 969 (PGGU2 Component - Marking and Labeling Systems Materials).

Features:
NECAL 4500 has excellent adhesion to most substrates, including polyethylene and polypropylene.

Physical Properties:
Composition: Rubber based adhesive
Release liner: Available with P, P1, W or W1 liner
Thickness: Total construction 1.0 – 2.0 mils dependent upon application
Scrim: 2 mil chrome, 2 mil brush chrome, 1 mil mylar, 2 mil mylar, and 4 mil mylar
Adhesion: 80-100 oz./in. | 40 – 50 oz./in. to polyethylene and polypropylene
Tensile: 70 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 170°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 4003 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 4003 is an unsupported film of pressure sensitive adhesive which displays very high tack and superior bond.

Features:
NECAL 4003 will adhere to many substrates.  It will bond to engineering plastics.  4003’s aggressive initial bond builds into a superior bond.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P, P1, W or W1 liner
Thickness: Total construction 1.0 – 2.0 mils dependent upon application
Scrim: 2 mil chrome, 2 mil brush chrome, 1 mil mylar, 2 mil mylar, and 4 mil mylar
Adhesion: 80-100 oz./in.
Tensile: 100 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 300°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 4001 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 4001 is an unsupported film of pressure sensitive adhesive which displays very high tack and superior bond, used only to manufacture label stock. It is UL recognized to Standard UL 969 (PGGU2 Component - Marking and Labeling Systems Materials).

Features:
NECAL 4001 will adhere to many substrates.  It will bond to engineering plastics.  4001’s aggressive initial bond builds into a superior bond.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P, P1, W or W1 liner
Thickness: Total construction 1.0 – 2.0 mils dependent upon application
Scrim: 2 mil chrome, 2 mil brush chrome, 1 mil mylar, 2 mil mylar, and 4 mil mylar
Adhesion: 80-100 oz./in.
Tensile: 100 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 195°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 3400 Removable Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 3400 is a supported film of removable pressure sensitive adhesive that displays good tack and adhesion but is easily removed with no residue from most surfaces.  A permanent adhesive is on one side of the polyester scrim and a removable adhesive is on the opposite side.  The permanent adhesive is intended to be bonded to the appliqué and the removable adhesive is intended to be bonded to the substrate.

Physical Properties:
Composition: Acrylic based adhesive (both sides)
Release liner: Available with P or W liner
Thickness: Total construction 5 mils
Scrim: 1 mil polyester
Adhesion: 200-220 oz./in. (removable)
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 195°F maximum

Bonding Instructions:
Apply to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact Necal Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.