Technical Data Sheets

NECAL 9512 Adhesive

Posted by Ed Johnson on Feb 4, 2011 1:22:00 PM

NECAL 9512 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 9512 is a supported film of pressure sensitive adhesive displaying excellent bond and initial tack.

Features:
NECAL 9512 is designed for polypropylene and polyethylene.  9512 adheres to many other substrates.  Because of its thickness 9512 is recommended for use on rough surfaces.  It has excellent die-cutting properties.

Physical Properties:
Composition: Modified Acrylic based Adhesive
Release liner: Available with P, W, H, HD, or VF liner
Thickness: Total construction 4.0 mils
Scrim: .00048 mil Polyester
Adhesion (PSTC-1 std.): 120 - 150 oz./in. (Aluminum/Polypropylene) 340 – 360 oz./in. (Aluminum/Stainless)
Tensile (Polyester to SS, 1 sq.in.): 225 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -20°F  to 270°F

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is at least two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

0 Comments Click here to read/write comments

Tags: Low Temperature, Necal Brand Products, Adhesive Transfer Tape, Acrylic PSA Adhesive, Double Coated Tape, High Tack Adhesive, VSB (very strong bond), Low Surface Energy, Mounting Tape, Die Cut Friendly, Very Die Cut Friendly

NECAL 8197-X Adhesive

Posted by Ed Johnson on Feb 4, 2011 10:28:00 AM

NECAL 8197-X Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 8197-X is a supported pressure sensitive adhesive that is used exclusively in “soft touch” applications.

Features:
NECAL 8197-X shows no adhesive ooze even after extensive aging.  Adhesion is good to most substrates including aluminum, steel, glass and many plastics including circuit board plastics.  Good initial bond will improve within a few hours or day to a superior bond.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P or W liner
Thickness: Total construction 1.5 mils on each side
Scrim: X (indicates total thickness with polyester film.  Example: 8197-7 is a 4 mil polyester with 1.5 mils adhesive each side.)
Adhesion (PSTC-1 std.): Initial: 100-120 oz./in. Aged: 170-180 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 130 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 60°F Minimum
Service temperature range: 0°F minimum to 225°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

0 Comments Click here to read/write comments

Tags: Necal Brand Products, Adhesive Transfer Tape, Acrylic PSA Adhesive, Double Coated Tape, Temperature Resistant, Double Linered Adhesive Transfer Tapes, Die Cut Friendly, Very Die Cut Friendly

NECAL 8194 Adhesive

Posted by Ed Johnson on Feb 4, 2011 10:17:00 AM

NECAL 8194 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 8194 is a supported pressure sensitive adhesive that has been designed for high performance requirements in “membrane switch” applications.

Features:
NECAL8194 exhibits excellent diecuttability and shows no adhesive ooze even after extensive aging.  Adhesion is good to most substrates exhibiting repositionability due to lower initial tack but will build to a superior bond after 24-48 hours.  8194, with excellent heat, UV and chemical resistance, is recommended for high performance applications.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P, W, H, HD, VF liner
Thickness: Total construction 5.0 mil
Scrim: .001 gauge polyester
Adhesion (PSTC-1 std.): Initial: 80-100 oz./in.  Aged: 170-180 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 130 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 60°F Minimum
Service temperature range: -40°F minimum to 400°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is at least two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

0 Comments Click here to read/write comments

Tags: Necal Brand Products, Adhesive Transfer Tape, Double Coated Tape, High Performance, Strong Bond, Double Linered Adhesive Transfer Tapes, Die Cut Friendly, Membrane Switch Spacer, Very Die Cut Friendly

All posts