NECAL 8195 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 8195 is a supported pressure sensitive adhesive displaying excellent tack.

Features:
NECAL 8195 will adhere to many substrates.  8195 is highly recommended for rough textured surfaces that have low contact areas.  It can be used where vibration deadening is required.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P or W liner
Thickness: Total construction 32 mil + or – 10%
Scrim: Polyurethane open-celled foam
Adhesion (PSTC-1 std.): 95 - 120 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 90 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 225°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 8194 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 8194 is a supported pressure sensitive adhesive that has been designed for high performance requirements in “membrane switch” applications.

Features:
NECAL8194 exhibits excellent diecuttability and shows no adhesive ooze even after extensive aging.  Adhesion is good to most substrates exhibiting repositionability due to lower initial tack but will build to a superior bond after 24-48 hours.  8194, with excellent heat, UV and chemical resistance, is recommended for high performance applications.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P, W, H, HD, VF liner
Thickness: Total construction 5.0 mil
Scrim: .001 gauge polyester
Adhesion (PSTC-1 std.): Initial: 80-100 oz./in.  Aged: 170-180 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 130 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 60°F Minimum
Service temperature range: -40°F minimum to 400°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is at least two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 8193 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 8193 is a supported pressure sensitive adhesive displaying high tack and good creep resistance. It is UL recognized to Standard UL 969 (PGGU2 Component - Marking and Labeling Systems Materials).

Features:
NECAL 8193 will adhere to many substrates.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P, W, H, HD, J, VF liner
Thickness: Total construction 4.0 mil
Scrim: .00048 mil polyester
Adhesion (PSTC-1 std.): 200-220 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 65 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 195°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 7114 Heat Activated Adhesive      Print Friendly Version

Adhesive Description:

NECAL 7114 is a unique unsupported heat activated adhesive.

Features:
NECAL 7114  displays high bond strengths to many substrates including vinyl, metal, a variety of plastics and various cloths and leathers.  7114 has excellent environmental resistance.

Physical Properties:
Adhesion: Cloth & vinyl destroying bond
Thickness: Total construction 1.0 mils
Service temperature range: -40°F minimum to 200°F maximum

Bonding Instructions:
Bonding instructions: 4-10 seconds at 325-375°F depending on materials bonded.  Minimum glue line temperature of 300°F and adequate pressure to initiate bonding required.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 3300 Removable Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 3300 is a supported film of removable pressure sensitive adhesive that displays good tack and adhesion but is easily removed with no residue from most surfaces.  A permanent adhesive is on one side of the polyester scrim and a removable adhesive is on the opposite side.  The permanent adhesive is intended to be bonded to the appliqué and the removable adhesive is intended to be bonded to the substrate.

Physical Properties:
Composition: Acrylic based adhesive (both sides)
Release liner: Available with P or W liner
Thickness: Total construction 3.5 mils
Scrim: .5 mil polyester
Adhesion: 5-10 oz./in. (removable)
Application temperature: 50°F Minimum
Service temperature range: 0°F minimum to 120°F maximum

Bonding Instructions:
Apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is at least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 3200 Removable Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 3200 is a supported removable pressure sensitive adhesive that displays good tack and adhesion but is easily removed with no residue from most surfaces.  A permanent adhesive is on one side of the polyester scrim and a removable adhesive is on the opposite side.  The permanent adhesive is intended to be bonded to the appliqué and the removable adhesive is intended to be bonded to the substrate.

Physical Properties:
Composition: Acrylic based adhesive (both sides)
Release liner: Available with P or W liner
Thickness: Total construction 3.5 mils
Scrim: .5 mil polyester
Adhesion: 10-20 oz./in. (removable).
Application temperature: 50°F Minimum
Service temperature range: 0°F minimum to 120°F maximum

Bonding Instructions:
Apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is at least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 1321 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

Features:
NECAL 1321 will adhere to many substrates, including aluminum, steel, brass, and most plastics.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P or W liner
Thickness: Total construction 60 mil + or – 10%
Scrim: White Polyethylene closed-cell foam
Adhesion (PSTC-1 std.): 95 - 120 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 90 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 225°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 psi. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.