NECAL 4003 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 4003 is an unsupported film of pressure sensitive adhesive which displays very high tack and superior bond.

Features:
NECAL 4003 will adhere to many substrates.  It will bond to engineering plastics.  4003’s aggressive initial bond builds into a superior bond.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P, P1, W or W1 liner
Thickness: Total construction 1.0 – 2.0 mils dependent upon application
Scrim: 2 mil chrome, 2 mil brush chrome, 1 mil mylar, 2 mil mylar, and 4 mil mylar
Adhesion: 80-100 oz./in.
Tensile: 100 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 300°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 4001 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 4001 is an unsupported film of pressure sensitive adhesive which displays very high tack and superior bond, used only to manufacture label stock. It is UL recognized to Standard UL 969 (PGGU2 Component - Marking and Labeling Systems Materials).

Features:
NECAL 4001 will adhere to many substrates.  It will bond to engineering plastics.  4001’s aggressive initial bond builds into a superior bond.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P, P1, W or W1 liner
Thickness: Total construction 1.0 – 2.0 mils dependent upon application
Scrim: 2 mil chrome, 2 mil brush chrome, 1 mil mylar, 2 mil mylar, and 4 mil mylar
Adhesion: 80-100 oz./in.
Tensile: 100 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 195°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 1330FP Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

Features:
NECAL 1330FP is a lightweight, conformable pressure sensitive tape for window flashing and housewrap film splicing.

Physical Properties:
Composition: Rubber based adhesive
Release liner: Available with W liner
Thickness: Total construction 30 mil + or – 10%
Scrim: White Polyethylene foam

(1)  Foam split failure
(2)  Tyvek split failure
(3)  All samples reinforced with 2 mil polyester film as test values exceeded foam strength.
(4)  Samples bonded at 20ºF, left at 20°F for 15 min. then tested at room temp.
(5)  Samples were taken down, had not failed and showed little or no movement.

Permeability
Water vapor transmission rate: .04 or less grams per hour
Water absorption: 200 or less grams per square meter
Permeability is based on foam material only without adhesive.  Testing with adhesive would reduce water vapor and absorption considerably.

Surface Preparation
All surfaces must be dry, smooth, and free of dust, dirt, and debris.  Any loose debris must be cleaned off before application.

Application:
Cut pieces to be adhered to length.  Remove release liner, position and smooth into place from one end to the other eliminating as many air pockets as possible.  Apply based on local code and or standard building practices.  Overlaps should be a minimum of 2 inches.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 1321 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

Features:
NECAL 1321 will adhere to many substrates, including aluminum, steel, brass, and most plastics.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P or W liner
Thickness: Total construction 60 mil + or – 10%
Scrim: White Polyethylene closed-cell foam
Adhesion (PSTC-1 std.): 95 - 120 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 90 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 225°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 psi. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.