NECAL 4003 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 4003 is an unsupported film of pressure sensitive adhesive which displays very high tack and superior bond.

Features:
NECAL 4003 will adhere to many substrates.  It will bond to engineering plastics.  4003’s aggressive initial bond builds into a superior bond.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P, P1, W or W1 liner
Thickness: Total construction 1.0 – 2.0 mils dependent upon application
Scrim: 2 mil chrome, 2 mil brush chrome, 1 mil mylar, 2 mil mylar, and 4 mil mylar
Adhesion: 80-100 oz./in.
Tensile: 100 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 300°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 4001 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 4001 is an unsupported film of pressure sensitive adhesive which displays very high tack and superior bond, used only to manufacture label stock. It is UL recognized to Standard UL 969 (PGGU2 Component - Marking and Labeling Systems Materials).

Features:
NECAL 4001 will adhere to many substrates.  It will bond to engineering plastics.  4001’s aggressive initial bond builds into a superior bond.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P, P1, W or W1 liner
Thickness: Total construction 1.0 – 2.0 mils dependent upon application
Scrim: 2 mil chrome, 2 mil brush chrome, 1 mil mylar, 2 mil mylar, and 4 mil mylar
Adhesion: 80-100 oz./in.
Tensile: 100 p.s.i.
Shear Adhesion: 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 195°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 3400 Removable Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 3400 is a supported film of removable pressure sensitive adhesive that displays good tack and adhesion but is easily removed with no residue from most surfaces.  A permanent adhesive is on one side of the polyester scrim and a removable adhesive is on the opposite side.  The permanent adhesive is intended to be bonded to the appliqué and the removable adhesive is intended to be bonded to the substrate.

Physical Properties:
Composition: Acrylic based adhesive (both sides)
Release liner: Available with P or W liner
Thickness: Total construction 5 mils
Scrim: 1 mil polyester
Adhesion: 200-220 oz./in. (removable)
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 195°F maximum

Bonding Instructions:
Apply to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is al least two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact Necal Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 3300 Removable Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 3300 is a supported film of removable pressure sensitive adhesive that displays good tack and adhesion but is easily removed with no residue from most surfaces.  A permanent adhesive is on one side of the polyester scrim and a removable adhesive is on the opposite side.  The permanent adhesive is intended to be bonded to the appliqué and the removable adhesive is intended to be bonded to the substrate.

Physical Properties:
Composition: Acrylic based adhesive (both sides)
Release liner: Available with P or W liner
Thickness: Total construction 3.5 mils
Scrim: .5 mil polyester
Adhesion: 5-10 oz./in. (removable)
Application temperature: 50°F Minimum
Service temperature range: 0°F minimum to 120°F maximum

Bonding Instructions:
Apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is at least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 3200 Removable Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

NECAL 3200 is a supported removable pressure sensitive adhesive that displays good tack and adhesion but is easily removed with no residue from most surfaces.  A permanent adhesive is on one side of the polyester scrim and a removable adhesive is on the opposite side.  The permanent adhesive is intended to be bonded to the appliqué and the removable adhesive is intended to be bonded to the substrate.

Physical Properties:
Composition: Acrylic based adhesive (both sides)
Release liner: Available with P or W liner
Thickness: Total construction 3.5 mils
Scrim: .5 mil polyester
Adhesion: 10-20 oz./in. (removable).
Application temperature: 50°F Minimum
Service temperature range: 0°F minimum to 120°F maximum

Bonding Instructions:
Apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 p.s.i. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is at least one year when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.

NECAL 1321 Pressure Sensitive Adhesive      Print Friendly Version

Adhesive Description:

Features:
NECAL 1321 will adhere to many substrates, including aluminum, steel, brass, and most plastics.

Physical Properties:
Composition: Acrylic based adhesive
Release liner: Available with P or W liner
Thickness: Total construction 60 mil + or – 10%
Scrim: White Polyethylene closed-cell foam
Adhesion (PSTC-1 std.): 95 - 120 oz./in.
Tensile (Polyester to SS, 1 sq.in.): 90 p.s.i.
Shear adhesion (Polyester to SS, 1000 grams/sq.in.): 7 days +
Application temperature: 50°F Minimum
Service temperature range: -40°F minimum to 225°F maximum

Bonding Instructions:
Remove the release liner and apply mask to clean, dry substrate.  Use firm pressure to obtain maximum contact.  Use of air, hydraulic or mechanical bonding press is recommended with pressure of 40-60 psi. with dwell time of 2-5 seconds.

Storage:
The shelf life of this material is two years when stored in a cool, dry place.

Notice:
The information shown here represents typical values that may vary with each application.  The values are not intended to be a performance guarantee.  Users should determine, prior to use, the suitability of this material for their application.

Please contact NECAL Corporation to discuss your project/application, seek additional information, receive a free sample or request a quote.